Why Understanding Essential Plumbing Skills is Essential When Installing a Bathtub
Why Understanding Essential Plumbing Skills is Essential When Installing a Bathtub
Blog Article
We've encountered the article about Installing A Bathtub below on the web and think it made good sense to discuss it with you over here.
Installing a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old bathtub is conveniently accessible, the project can move immediately; if you have to open a wall to remove the old tub and also place the new bath tub, the task is much harder. In either case, the project is within a house handyman's skills, although you will require an assistant to leave the old tub and also set in the brand-new one. Make sure you have qualified on your own for the work and fit trying it. As opposed to employing a professional to take control of a halfway-completed job, it is far better to think about employing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your restroom if you have currently gotten a new tub and also do not require to change the setup of your previous supply of water pipelines.
Your tools and also material list must consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the restricted gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washing machines remain in place in between the faucet and the sink. Protect the tap in position with the maker offered backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type should be attached to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water and inspect all joints and also new pipework for leakages and also tighten them if necessary. Fill the tub as well as also inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the maker's instruction manual. Tiling and also securing around the tub should wait up until the bathtub has been utilized a minimum of once as this will certainly resolve it into its last setting.
Preparing for the Installment
Firstly, the sustaining framework supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the flexible tap connectors to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack a rigid seal, triggering the water to pass through the wall between the bathroom and also the tiling, resulting in complications with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the bathtub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can split relatively very early if you do not take into account this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is advisable to fit the tiles using waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader about How to Install a Bathtub, I imagined sharing that chunk was a smart idea. Sharing is good. Helping others is fun. I thank you for reading our article about How to Install a Bathtub.
24/7 ready, dial! Report this page